This addressable Warm White COB LED strip delivers a cosy, dot-free 3000K white on a single spotless 10mm tape, with each section individually controllable pixel by pixel over SPI or DMX. Unlike a standard single-colour white strip that lights up as one continuous run, this digital version lets you address the strip in segments - for running/chasing effects, sequential switch-on and zoned brightness control - all from one 24V strip.
|
Parameter |
Value |
|
SKU |
COBD-420-WW-503 |
|
Chip type |
COB (Spotless) |
|
Light type |
Warm White (single colour) |
|
Colour temperature |
3000K (Warm White) |
|
LEDs per metre |
420 |
|
Voltage |
24V DC |
|
Power per metre |
11W |
|
Luminous flux |
910 lm/m |
|
CRI |
Ra90 |
|
Ingress protection |
IP20 (non-waterproof) |
|
Strip width |
10mm |
|
Copper trace thickness |
2oz |
|
PCB layers |
Double layer (PRO Version) |
|
Control protocol |
Addressable Digital SPI / DMX |
|
Roll length |
30m (full roll) |
Choose this addressable Warm White version if you want segment-level control of a single warm white - running effects, sequential switch-on (great for stairs) or zoned dimming - rather than the whole strip behaving as one. If you simply need plain 3000K white that switches on together, a standard (non-addressable) white COB strip will be simpler and cheaper to run. The 3000K tone here is warm and cosy; pick 4000K for a neutral, daylight-balanced white. This is an IP20 strip for dry indoor use only; for moisture-prone areas (bathroom, kitchen splash zones, outdoors), choose a waterproof IP-rated version.
This strip runs on a dedicated 24V DC power supply and cannot be connected directly to mains - size the driver with roughly 20% spare headroom. Because it is addressable, it also needs a compatible SPI / DMX controller or decoder to drive the data line; a plain on/off or analog dimmer alone won't unlock the effects. Cut only at the marked cut points along the strip, and mount it in a suitable aluminium profile for the best heat dissipation and finish.
The strip is divided into individually controllable segments, so you can run effects like sequential switch-on, chasing and zoned brightness — even though it's a single 3000K warm white rather than colour.
3000K is a warm, cosy white that suits homely, relaxed spaces; 4000K is a neutral, daylight-balanced white that looks cleaner and more functional. Everything else about the strip stays the same.
No — it's rated IP20 with no protection against moisture. For wet or outdoor areas, choose a waterproof (IP-rated) version instead.
Yes. To use the addressable effects it needs an SPI / DMX-compatible controller or decoder, plus a standard 24V DC driver for power.
| HUE Color | 3000K Warm White |
|---|---|
| Watts per meter | 11 |
| Water Resistance | IP20 Non Waterproof |
| Voltage | 24V |
| Lumens per meter | 910 |
| Number of LEDs/ Meter | 480 |
This addressable Warm White COB LED strip delivers a cosy, dot-free 3000K white on a single spotless 10mm tape, with each section individually controllable pixel by pixel over SPI or DMX. Unlike a standard single-colour white strip that lights up as one continuous run, this digital version lets you address the strip in segments - for running/chasing effects, sequential switch-on and zoned brightness control - all from one 24V strip.
|
Parameter |
Value |
|
SKU |
COBD-420-WW-503 |
|
Chip type |
COB (Spotless) |
|
Light type |
Warm White (single colour) |
|
Colour temperature |
3000K (Warm White) |
|
LEDs per metre |
420 |
|
Voltage |
24V DC |
|
Power per metre |
11W |
|
Luminous flux |
910 lm/m |
|
CRI |
Ra90 |
|
Ingress protection |
IP20 (non-waterproof) |
|
Strip width |
10mm |
|
Copper trace thickness |
2oz |
|
PCB layers |
Double layer (PRO Version) |
|
Control protocol |
Addressable Digital SPI / DMX |
|
Roll length |
30m (full roll) |
Choose this addressable Warm White version if you want segment-level control of a single warm white - running effects, sequential switch-on (great for stairs) or zoned dimming - rather than the whole strip behaving as one. If you simply need plain 3000K white that switches on together, a standard (non-addressable) white COB strip will be simpler and cheaper to run. The 3000K tone here is warm and cosy; pick 4000K for a neutral, daylight-balanced white. This is an IP20 strip for dry indoor use only; for moisture-prone areas (bathroom, kitchen splash zones, outdoors), choose a waterproof IP-rated version.
This strip runs on a dedicated 24V DC power supply and cannot be connected directly to mains - size the driver with roughly 20% spare headroom. Because it is addressable, it also needs a compatible SPI / DMX controller or decoder to drive the data line; a plain on/off or analog dimmer alone won't unlock the effects. Cut only at the marked cut points along the strip, and mount it in a suitable aluminium profile for the best heat dissipation and finish.
The strip is divided into individually controllable segments, so you can run effects like sequential switch-on, chasing and zoned brightness — even though it's a single 3000K warm white rather than colour.
3000K is a warm, cosy white that suits homely, relaxed spaces; 4000K is a neutral, daylight-balanced white that looks cleaner and more functional. Everything else about the strip stays the same.
No — it's rated IP20 with no protection against moisture. For wet or outdoor areas, choose a waterproof (IP-rated) version instead.
Yes. To use the addressable effects it needs an SPI / DMX-compatible controller or decoder, plus a standard 24V DC driver for power.
Loading...
+353 24 904 96
