This Natural White COB LED strip delivers a clean, dot-free 4000K light on a slim 10mm tape, pairing near-top brightness in the COB Spotless series (1940 lm/m) with a neutral, daylight-balanced tone that suits almost any room. The spotless COB face gives one continuous line of light with no visible LED points, while the PRO build - double PCB layer with 3oz copper paths - keeps voltage drop and running temperature low over long runs.
|
Parameter |
Value |
|
SKU |
CSP-320-NW-476 |
|
Chip type |
COB (Spotless) |
|
Light type |
Natural White (single colour) |
|
Colour temperature |
4000K (Natural White) |
|
LEDs per metre |
320 |
|
Voltage |
24V DC |
|
Power per metre |
15W |
|
Luminous flux |
1940 lm/m |
|
CRI |
Ra90 |
|
Beam angle |
>160° |
|
Ingress protection |
IP20 (non-waterproof) |
|
Strip width |
10mm |
|
Copper trace thickness |
3oz |
|
PCB layers |
Double layer (PRO Version) |
|
Cut points |
Every 2.5cm (25mm) |
|
Lifespan |
50,000h |
|
Roll length |
30m (full roll) |
|
Warranty |
5 years |
Choose this 4000K Natural White version if you want a neutral, daylight-balanced white that works almost anywhere - clean and functional without looking either warm or cold. The same COB Spotless series is also available in 6000K Cold White (the brightest and crispest), 3000K Warm White and 2700K Soft Warm; go cooler for maximum clarity, warmer for a cosier feel. At 1940 lm/m this is one of the brightest whites in the range. It's an IP20 strip for dry indoor use only; for moisture-prone areas (bathroom, kitchen splash zones, outdoors), choose a waterproof IP-rated version.
This strip requires a dedicated 24V DC power supply and cannot be connected directly to mains - size the driver with roughly 20% spare headroom (the configurator suggests ~18W or higher per metre). A controller is only needed if you want dimming; for a fixed Natural White strip like this, a simple 24V driver is sufficient. Cut only at the marked cut points (every 2.5cm), and mount it in a suitable aluminium profile for the best heat dissipation and finish.
4000K is a neutral, daylight-balanced white that suits almost any room; 6000K is a crisper, brighter cool-daylight tone. Choose 4000K for a natural everyday look, 6000K for maximum clarity.
4000K is neutral and clean; 3000K is warmer and cosier. Everything else about the strip stays the same.
Every 2.5cm (25mm), at the marked cut points — trimming there won't damage the rest of the strip.
No — it's rated IP20 with no protection against moisture. For wet or outdoor areas, choose a waterproof (IP-rated) version instead.
No. It runs from a standard 24V DC driver. You only need a controller if you want dimming.
| HUE Color | 4000K Natural White |
|---|---|
| Watts per meter | 15 |
| Water Resistance | IP20 Non Waterproof |
| Voltage | 24V |
| Lumens per meter | 1940 |
| Number of LEDs/ Meter | 320 |
This Natural White COB LED strip delivers a clean, dot-free 4000K light on a slim 10mm tape, pairing near-top brightness in the COB Spotless series (1940 lm/m) with a neutral, daylight-balanced tone that suits almost any room. The spotless COB face gives one continuous line of light with no visible LED points, while the PRO build - double PCB layer with 3oz copper paths - keeps voltage drop and running temperature low over long runs.
|
Parameter |
Value |
|
SKU |
CSP-320-NW-476 |
|
Chip type |
COB (Spotless) |
|
Light type |
Natural White (single colour) |
|
Colour temperature |
4000K (Natural White) |
|
LEDs per metre |
320 |
|
Voltage |
24V DC |
|
Power per metre |
15W |
|
Luminous flux |
1940 lm/m |
|
CRI |
Ra90 |
|
Beam angle |
>160° |
|
Ingress protection |
IP20 (non-waterproof) |
|
Strip width |
10mm |
|
Copper trace thickness |
3oz |
|
PCB layers |
Double layer (PRO Version) |
|
Cut points |
Every 2.5cm (25mm) |
|
Lifespan |
50,000h |
|
Roll length |
30m (full roll) |
|
Warranty |
5 years |
Choose this 4000K Natural White version if you want a neutral, daylight-balanced white that works almost anywhere - clean and functional without looking either warm or cold. The same COB Spotless series is also available in 6000K Cold White (the brightest and crispest), 3000K Warm White and 2700K Soft Warm; go cooler for maximum clarity, warmer for a cosier feel. At 1940 lm/m this is one of the brightest whites in the range. It's an IP20 strip for dry indoor use only; for moisture-prone areas (bathroom, kitchen splash zones, outdoors), choose a waterproof IP-rated version.
This strip requires a dedicated 24V DC power supply and cannot be connected directly to mains - size the driver with roughly 20% spare headroom (the configurator suggests ~18W or higher per metre). A controller is only needed if you want dimming; for a fixed Natural White strip like this, a simple 24V driver is sufficient. Cut only at the marked cut points (every 2.5cm), and mount it in a suitable aluminium profile for the best heat dissipation and finish.
4000K is a neutral, daylight-balanced white that suits almost any room; 6000K is a crisper, brighter cool-daylight tone. Choose 4000K for a natural everyday look, 6000K for maximum clarity.
4000K is neutral and clean; 3000K is warmer and cosier. Everything else about the strip stays the same.
Every 2.5cm (25mm), at the marked cut points — trimming there won't damage the rest of the strip.
No — it's rated IP20 with no protection against moisture. For wet or outdoor areas, choose a waterproof (IP-rated) version instead.
No. It runs from a standard 24V DC driver. You only need a controller if you want dimming.
Loading...
+353 24 904 96
