+353 24 904 96
LED Strip COB RGB • Spotless • 24V • 15W • IP20 • 620lm • 10mm • 2oz Cooper paths PRO Version
In stock
SKU
COB-840-RGB-360
LED Strip COB RGB Spotless
This LED Strip COB RGB is a spotless, colour-changing strip built for smooth accent and mood lighting indoors, where you want a continuous line of colour with no visible dots. Unlike the single-colour siblings in this series (COB Red, COB Blue) or the tunable-white COB CCT, this variant covers the full RGB spectrum from one strip, so a single run can shift through millions of colours via an RGB controller. The COB (Chip-on-Board) construction packs the diodes into a continuous phosphor line, which is what removes the dotting effect you see on standard SMD RGB tape.
Key Features
- COB spotless design: one continuous line of light with no visible diodes or hotspots
- Full RGB colour changing: the whole colour spectrum from a single strip using an RGB controller
- 840 LEDs/m: dense diode layout for smooth, even colour blending along the run
- Wide beam angle over 160°: broad, soft light spread for washes and coves
- Double PCB layer with 2oz copper paths: lower voltage drop and cooler operation over long runs
- 24V design: less power loss on longer runs than 12V equivalents
- 50,000h rated lifespan: long service life for permanent installations
Technical Specification
|
Parameter |
Value |
|
SKU |
COB-840-RGB-360 |
|
Chip type |
COB |
|
Colour |
RGB (colour changing) |
|
LEDs per metre |
840 |
|
Voltage |
24V |
|
Power per metre |
15W |
|
Luminous flux |
620 lm/m |
|
Ingress protection |
IP20 (non-waterproof) |
|
Strip width |
10mm |
|
Strip thickness (IP20) |
1.6mm |
|
Beam angle |
over 160° |
|
PCB layers |
Double layer |
|
Copper trace thickness |
2oz |
|
Cut points |
every 50mm |
|
Reel length |
10m |
|
Lifespan |
50,000h |
Which Version Should You Choose?
Choose this RGB variant if you want full colour changing from one strip - ideal for feature lighting, mood scenes and dynamic effects. If you only need a single fixed colour, the COB Red or COB Blue versions of the same series are simpler and don't require an RGB controller; if you want adjustable white light rather than colour, look at the COB CCT 2700-6500K variant instead. This is an IP20 strip, so it's for dry indoor use only - if the install will face moisture (bathroom, kitchen splash zone, or outdoors), choose a waterproof IP66 strip instead.
Applications
- Cove and ceiling lighting in dry indoor spaces
- Accent and mood lighting for living rooms and bedrooms
- Bar, counter and back-of-shelf display lighting
- Feature walls and architectural detailing
- Entertainment, media and gaming setups
- Retail and display lighting in enclosed spaces
Installation
This strip runs on a dedicated 24V DC power supply and cannot be connected directly to mains voltage. Because it's a colour-changing strip, it also needs an RGB controller to switch and mix colours. For a 1m length, plan for a power supply of 18W or higher (strip wattage plus roughly 20% headroom); size the driver up for longer runs. The strip can be trimmed every 50mm at the marked cut points, and mounts via its adhesive back or inside an aluminium profile for better heat dissipation on continuous runs.
FAQ
Do I need a controller for this RGB strip?
Yes. RGB colour changing requires an RGB controller between the power supply and the strip — without it you can't switch or mix colours.
Can I use this strip in a bathroom or outdoors?
No. IP20 has no protection against moisture or splashes. For a bathroom, kitchen splash zone or outdoor use, choose a waterproof IP66 strip instead.
What's the difference between COB RGB and standard SMD RGB?
COB uses a continuous line of tightly packed diodes under a phosphor coating, so the light looks like an unbroken line with no dots. Standard SMD RGB shows individual diodes and visible spacing.
How often can this strip be cut?
Every 50mm, at the marked cut points — trimming there won't damage the rest of the strip.
More Information
| Color Changing | RGB |
|---|---|
| Watts per meter | 15 |
| Water Resistance | IP20 Non Waterproof |
| Voltage | 24V |
| Lumens per meter | 620 |
| Number of LEDs/ Meter | 840 |
Reviews
Write Your Own Review
Related Products
We found other products you might like!
-
LED Profile • SURFACE • "X" • SILVER • Aluminium • 2.02 Meters length • PRO • multi set •From €12.83 €10.43
To €26.21 €21.31
-
LED Profile • SURFACE • "Y" • SILVER • Aluminium • 2.02 Meters length • PRO • multi set •From €25.83 €21.00
To €42.24 €34.34
-
LED Profile • SURFACE • "Y" • WHITE • Aluminium • 2.02 Meters length • PRO • multi set •From €28.08 €22.83
To €44.49 €36.17
-
LED Profile • SPECIAL APP • FURNITURE • "COSMO" • SILVER • Aluminium • 2.02 Meters length • PRO • multi set •From €38.04 €30.93
To €53.71 €43.67
-
LED Profile • SURFACE • ARCHITECTURAL • SUSPENDED • "SILEDA" • WHITE • Aluminium • 2.02 Meters length • PRO • multi set •From €37.13 €30.19
To €82.69 €67.23
-
LED Profile • RECESSED • ARCHITECTURAL • PLASTER IN • "TIANO" • SILVER • Aluminium • 2.02 Meters length • PRO • multi set •From €70.22 €57.09
To €90.70 €73.74
LED Strip COB RGB Spotless
This LED Strip COB RGB is a spotless, colour-changing strip built for smooth accent and mood lighting indoors, where you want a continuous line of colour with no visible dots. Unlike the single-colour siblings in this series (COB Red, COB Blue) or the tunable-white COB CCT, this variant covers the full RGB spectrum from one strip, so a single run can shift through millions of colours via an RGB controller. The COB (Chip-on-Board) construction packs the diodes into a continuous phosphor line, which is what removes the dotting effect you see on standard SMD RGB tape.
Key Features
- COB spotless design: one continuous line of light with no visible diodes or hotspots
- Full RGB colour changing: the whole colour spectrum from a single strip using an RGB controller
- 840 LEDs/m: dense diode layout for smooth, even colour blending along the run
- Wide beam angle over 160°: broad, soft light spread for washes and coves
- Double PCB layer with 2oz copper paths: lower voltage drop and cooler operation over long runs
- 24V design: less power loss on longer runs than 12V equivalents
- 50,000h rated lifespan: long service life for permanent installations
Technical Specification
|
Parameter |
Value |
|
SKU |
COB-840-RGB-360 |
|
Chip type |
COB |
|
Colour |
RGB (colour changing) |
|
LEDs per metre |
840 |
|
Voltage |
24V |
|
Power per metre |
15W |
|
Luminous flux |
620 lm/m |
|
Ingress protection |
IP20 (non-waterproof) |
|
Strip width |
10mm |
|
Strip thickness (IP20) |
1.6mm |
|
Beam angle |
over 160° |
|
PCB layers |
Double layer |
|
Copper trace thickness |
2oz |
|
Cut points |
every 50mm |
|
Reel length |
10m |
|
Lifespan |
50,000h |
Which Version Should You Choose?
Choose this RGB variant if you want full colour changing from one strip - ideal for feature lighting, mood scenes and dynamic effects. If you only need a single fixed colour, the COB Red or COB Blue versions of the same series are simpler and don't require an RGB controller; if you want adjustable white light rather than colour, look at the COB CCT 2700-6500K variant instead. This is an IP20 strip, so it's for dry indoor use only - if the install will face moisture (bathroom, kitchen splash zone, or outdoors), choose a waterproof IP66 strip instead.
Applications
- Cove and ceiling lighting in dry indoor spaces
- Accent and mood lighting for living rooms and bedrooms
- Bar, counter and back-of-shelf display lighting
- Feature walls and architectural detailing
- Entertainment, media and gaming setups
- Retail and display lighting in enclosed spaces
Installation
This strip runs on a dedicated 24V DC power supply and cannot be connected directly to mains voltage. Because it's a colour-changing strip, it also needs an RGB controller to switch and mix colours. For a 1m length, plan for a power supply of 18W or higher (strip wattage plus roughly 20% headroom); size the driver up for longer runs. The strip can be trimmed every 50mm at the marked cut points, and mounts via its adhesive back or inside an aluminium profile for better heat dissipation on continuous runs.
FAQ
Do I need a controller for this RGB strip?
Yes. RGB colour changing requires an RGB controller between the power supply and the strip — without it you can't switch or mix colours.
Can I use this strip in a bathroom or outdoors?
No. IP20 has no protection against moisture or splashes. For a bathroom, kitchen splash zone or outdoor use, choose a waterproof IP66 strip instead.
What's the difference between COB RGB and standard SMD RGB?
COB uses a continuous line of tightly packed diodes under a phosphor coating, so the light looks like an unbroken line with no dots. Standard SMD RGB shows individual diodes and visible spacing.
How often can this strip be cut?
Every 50mm, at the marked cut points — trimming there won't damage the rest of the strip.
Write Your Own Review
